Jump to content

All Activity

This stream auto-updates

  1. Today
  2. Nice find, I love barn finds, It wil keep you buzzy for a while
  3. Jimxxx, thanks I replaced, a burned resistor,in the area. Will test the transistor if it's not damaged
  4. Hi, assuming this is similar to other mpu1 and mpu2 schematics then the speaker is connected to pin 15 on the blue with its other side going to pin2 (+15v). Again assuming there are no loose connections or dry joints on the board in that area then i would check the transistor connected to pin 15 which i think is T19. probably the one with the brownest resistor area as seen below. Good luck and post some pics.
  5. Hi all, a new project is arrived number 6 😆 Barcrest Mpu2 Starlight I have a problem, and worked in the past on same problem. but can't think the solution . I have no sound, mpu is stable (need revision) wen i swap the mpu, with spare I have sound. So, problem is the board.
  6. Yesterday
  7. Hello !! Phil has a bit of work to do, but it’s great that he found It. In any case, you have better luck than we do in France when it comes to finding machines to add to a collection. Machines of this type are rare or hard to come by here. Best of luck with the rest of your project! Thank you for the information.
  8. Last week
  9. Yes there is, but they are nearly all digital s**t. But hey that’s just my opinion and other opinions are available. There are still arcades with old school machines around the country.
  10. Hello, Great find. I had a question: in your country, are there still slot machines in operation— in pubs, bars, or elsewhere—or are they prohibited, as they are in France? Thanks.
  11. Great find phil , and a £3 original too
  12. I know Ron, would look nice beside my lucky 2's but I need to thin out
  13. If only I had room I would go for that little gem.
  14. The green LED is power, it should stay lit. The red LED is reset, it should come on for a couple of seconds then go off and stay off. If it comes back on then the board is stuck in reset. Try turning off all the switches on SW1 and powering up.
  15. The green LED is power, it should stay lit. The red LED is reset, it should come on for a couple of seconds then go off and stay off. If it comes back on then the board is stuck in reset. Try turning off all the switches on SW1 and powering up.
  16. The green LED is power, it should stay lit. The red LED is reset, it should come on for a couple of seconds then go off and stay off. If it comes back on then the board is stuck in reset. Try turning off all the switches on SW1 and powering up.
  17. Been offered this but it’s too far for me! It’s down in Surrey I told the guy it would be worth around £100. If anyone here is interested?
  18. Bjour à tous jai demarer une autre discussion das section des nouveaux mais je ne peux pas consulter les message d'erreur ex0 du coup jen tente une autre ici pour le coup voici la machine en question équiper d'une carte simple astra IO-3 intégrer La carte reste mais le processeur reste figer led rouge fixe verte fixe aussi
  19. Bjour à tous jai demarer une autre discussion das section des nouveaux mais je ne peux pas consulter les message d'erreur ex0 du coup jen tente une autre ici pour le coup voici la machine en question équiper d'une carte simple astra IO-3 intégrer La carte reste mais le processeur reste figer led rouge fixe verte fixe aussi
  20. Bjour a tous jai demarer une autre discutions das section des nouveau mais je ne peux pas consulter les message erreur ex0 du coup jen tente une autre ici pour le coup voici la machine en question équiper d'une carte mere astra IO-3 integrate La carte demare mais le processeur reste figer led rouge fixe verte fixe aussi
  21. The green LED is power, it should stay lit. The red LED is reset, it should come on for a couple of seconds then go off and stay off. If it comes back on then the board is stuck in reset. Try turning off all the switches on SW1 and powering up.
  22. Hi Snou Sorry to say it is not a tech i have had anything to do with so i have no idea what the sequence of the LEDs is. But from looking at the photo of the PCB, how bad is the leakage in the battery are? Can you take a close up photo of that area? Also i would want to check the integrity of U1 EPROM as the label has fallen of its window and if this has been exposed to light / sunlight for a period of time it could have damaged the program. Just to save anyone having to use translate i have attached it below. Cheers Jim +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ Hello everyone! I’m new here—my nickname is Snou, and I live in France/ I’m reaching out because I own a "Club Millionaire" slot machine made by Astra. The machine is complete, but it won’t turn on. The power supply seems fine and is delivering power. Regarding the main circuit board, the battery (the "pill") had leaked and has since been replaced. The two LEDs light up, but they remain steady (they don’t flash). Could you please help me? Best regards, Snou ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
  23. Earlier
  24. Bonjour à tous ! Je suis nouveau, je me surmôme snou et je vie en france Je viens vers vous car je pocede une machine a sous club millionnaire de la marque astra , La machine et complète mais ne sallume pas L'alimentation me semble bonne et délivre du courant Concernant la carte simple la pilule à couler et à etais changer Les 2 LED s'allument mais restent fixes Pourriez-vous maider ? Cordialement, Snou
  25. Bonjour à tous ! Je suis nouveau, je me surmôme snou et je vie en france Je viens vers vous car je pocede une machine a sous club millionnaire de la marque astra , La machine et complète mais ne sallume pas Lalimentation me semble bonne et délivre du courant Concernant la carte simple la pilule à couler et à etais changer Les 2 LED s'allument mais restent fixes Pourriez-vous maider ? Cordialement, Snou
  26. I now have everything i need for this one
  27. Does anyone have an Electrocoin BAR-X machine where they can test / give feedback about my prototype reproduction board. The board "Universal 8205" is found in the very early BAR-X machines. You would just need to transplant the eprom's from your board. I'm happy to post to you and provide a return label.
  1. Load more activity
×
×
  • Create New...