All Activity

hi i m actually looking for 20,10,50P Tube payout Mech of ACE 100 Fruit Machine because of my Climber one is an export with no payout mech (1937 french law 😕 ). if someone want to sell some, i m interested. i dont know the original reference. regards

IVE GOT A PROBLEM. THE new classic layout dont let you go into test mode the door switches dont work. i need to force play so i can see the memoyr debugger for the cash prixe as ive incresed it to 1.50p and ive increased the nudges from 4 to 12 instead of 1 to 8. the nudges work brilliant. the 1.50p will pick the 1 but the animation steps are still 20p to 1 pound. i will be there forever. is there no old version of this on older mfmes

MDM 1981

Can't say I have. This was a time where everybody and their dog was making rebuilds. Some like this are quite tasteful. Some...not so much Nice to see it emulated maybe in the future. It probably runs the same tech Good find! Oldskooler

As anyone seen this sru before I will be picking it up next week ( clone of an lite a nudge ,, 10p play £2 token jackpot

https://www.ebay.co.uk/itm/371532527747

Pinball Heaven stock them on eBay. https://www.ebay.co.uk/itm/371532527747

I’ve had a bit of time again, this time to work on the mechanism control sequence timer. This one was also covered in rust and grime. The gearbox was almost seized up; I could barely turn it by hand, but luckily a bit of penetrating oil did the trick. That could easily have cost me the motor. I’ve also started dismantling the door; I’d already taken it off. So that various parts can be soaked in cleaning vinegar.

what is everyone favourite machine on here

Thanks now with a happy new owner, razzle dazzle is next

Hi, Great restoration work. Congratulations.

Well done, it looks good, nicely repaired

No problem 😉

Yes, of course, Daveo138 and Sulzerned, it is in the Netherlands. link : GE44 6volt 2watt 10mm bajonetlamp

Second that from daveo. Great ro know where we can get a few

Sorted thankyou both of you

Do you have a link?

Thanks, Sulzerned. Luckily, I was able to buy them from an online pinball shop.

Great work.again . Glad you managed to get hold of the 6v bulbs too.

It was time to clean the credit count sequence timer; it was dirty and covered in rust. It was quite a job to get it apart. Fortunately, I’d already replaced the AMP plugs on the switches. After a thorough clean, something wasn’t quite right when I was putting it back together – I kept losing the screws from the switch terminals. It turned out I’d turned the 4-sided rod the wrong way round, which meant the screws didn’t fit. So I took it apart again and paid close attention this time. Some new bulbs (6V 2W) had also arrived, so I replaced them straight away. I also fitted new film capacitors for the RC snubbers. The old ones were already starting to crack and their capacitance was barely there.

Looks good, nicely done. I’ve done it myself before; mine was glued and bolted.

TTX, That looks good. Do you have any more details? What kind of material did you print on?

Hi does anyone know which pin on the scorp 2 board is the input pin for 20p's? Its Deluxe Cops n Robbers Club. Accepts and sorts 20p coins fine but does not credit them. I would have put new sockets on the scorp2 FPGA chips so it won't be related to that. Ive not looked at it yet but cant tell if its wiring, mech or board. Thanks

Yes, I’d say so too, sulzerned that’s what I’m planning to do as well

I’ve just tested it, and it works; I’m using MFME V20. You’ll need a newer version.