All Activity

Need some help with my hi roller mps 2 it was working fine after a clean up of the battery are and removing that edge connector and checking all the traces and via’s, although the sound was a bit hit or miss at times! anyway it died on me again and to my surprise I could see some green had formed on the cpu pins ! Clearly I did not clean it up properly so I did do the area with vinegar then washed it went over with ipa dried it with compressed air, did some more via’s directly under the battery but it’s now all over the place ! Did a short video to show the behaviour any advice welcome thanks Ronnie IMG_5601.mov

Yep, it does make it an MPU2. They obviously made these before the MPU2 was released to give the extra functionality, and then developed it into the MPU2. Managed to get it working today.

Maybe for star nudge video? Jan 1980.

Now that is certainly different! I assume it makes a mpu1 into a mpu2?

Wow never seen that before either bob .er silly question but what Does the add on baord do and why is it there ?

Well I thought I'd seen everything about the MPU2 until I received this today. Not sure what to call it, Frankenstein perhaps or just MPU1 ½? It's a bog standard MPU1 with an add on chassis! The two boxes are bolted together and a patch cable links the two boards. There is also a small sub board for the outputs.

welcome

Howdy people, does anyone have any win plan decals for this? Or any other spares? Thanks

Hi everyone great forum my name is saj

Well,I have to admit..18 years have passed, and I'm still none the wiser. But my kids have grown, and left!! The bell fuit machine, I kind of recall. They had another called rubies and diamonds, which was a 2 quid / 4 quid repeater, respectively. System 80??. They could go mental, as Pete has testified. I don't think the resources have found these machines. Yet. Statto

Yes Bob, you are right "o/ and i/p are sortie et entrée" en français. So, about Cop499, al the pins are 0 volt except pin 8 which is 5 Volts (Vcc). No waves.

Desole Julalain.... I use o/p to be short for output (i/p for input). Would that be 'sortie et entree en Francais'?

There are retro arcades dotted around there is a bowling alley in Preston that has old machines to play

A- up to you B - licensing to let people play, costs money. Premises also cost money. Parts and overheads cost money. Also, loads of people out there like to hit machines when they don’t win, why would somebody risk that? C - Get buying, or visit some classic amusements. Some people call stuff from 20 years “old school” some people are talking about 40 years ago. If you’re talking about stuff from 90’s/00’s there’s plenty of places to visit

Pin 16 on the Z80 (IC9) goes to pin 12 on the CTC (IC8) and pin 17 on the Z80 goes to pin 13 on the CTC. I think that I'm going to redo the small board because there are poor contacts sometimes. IC2 cop499 Pins 1, 2, 3, 4, 5 (ground), 6, 7 are 0 volts, Pin 8 is 5,2 volts. IC1 CD4069 Pin 1, 3, 9, 11, 13 and 14 are 5,2 Volts. Pins 2, 4, 5, 7, 8, 10 and 12 are 0 Volt. Pin 6 is 0,74 Volt. IC3 ILD74 Pins 1 and 2 are +12 Volts. Pin 8 is -12 Volts. Pins 3 and 4 are volt. Pin 7 is 4,80 Volts.

Hi, I am new here but use to play emulated fruit machines from back in the good old days. I have been wondering laterly: a) Should i buy a machine b) Why is there no place to go to play free play old school fruit machines c) I want to play old school fruit machines again like i use to many years ago!

Oups, you are right again. Pin 26 on the Z80 is the reset and on the CTC pin 17 is the reset. My diagram is wrong. I hope that there are no other mistakes... I'm sorry but what does o/p means ? P10 pin 6 goes to P3 pin 13 (RU2-RU6 and pin 12 of IC2) Here is the modified diagram.

Pin 26 on the Z80 should be the RESET, pin 17 is NMI which usually should be pulsing but if it's connected to the RESET line that would explain it. Not sure why that should be as my knowledge runs out at that point? Pin 16 isn't on the diagram which is the INT line, also inactive. There's folks on here a lot cleverer than me that would be able to explain this. OK so it would appear that IC13 is ROM1 and that one is enabled so it looks like it's reading it.🤞 Tracing the o/p of the COPP chip via the isolator chip IC3 pin7? The diagram shows P10 pin 6 and P1 pin 13 which goes to IC2 pin 12. So where does P10 pin 6 go?

I think I did not answer the question about the pins completely. Pins 16, 17, 23, 24 abnd25 are not pulsing but, Pin 16 is 0 volts, pin 17 (reset) is 5 Volts, pin 23 is 3,70 Volts and pins 24 and 25 are 5Volts.

About the roms, the info written are half erased. I think I read on IC13 R 1-7, on IC14 R 2-7 and on IC15 R 3-7 but I'm not sure. I checked the CPU (IC9 MK3880 Z80 CPU) pins you asked me about and some are inactive. 19, 20, 21, 22 are pulsing but 16, 17, 23, 24 and 25 are not.

thanks for reply trying to help someone who has a dond box23 and only has 100 days left on ive seen some dongles and they are dedicated ones lable on the end say c/d but his doesnt have anything on the end of his sticker

Can't confirm sorry as we've only had Cat C machines, but I thought Cat D didn't need the dongle same as the clubbers

Hi can a universal cat c dongle work on a £5 machine or can you buy a lifetime cat d but ive never seen one as the one in machine at the moment only has 100 days left any info much appreciated

Is there no info written on the ROM window cover labels? Even if it's only P1, P2 or P3 so we know which is which.

You are right, nothing to compare the ROM codes, I tried to contact someone who had the same machine ten years ago, but he does not answer me. IC 13, IC 14 and IC15 are 2716. I attached the ROM files on april the 18th and you saw in ROM 3 'COPYWRITE RETAINED BY FBN ELECTRONIC SYSEMS LTD' Maybe that' the problem