Jump to content

All Activity

This stream auto-updates

  1. Past hour
  2. Blimey Ronnie this is turning into a real poser??? Without the chip in (IC18) is the power and ground good to pins 16 and 8 ie don't use any other ground. Next what does the resistance measure from pin 12 to ground? Also check the via isn't broken on pin 12 ie make sure there's connectivity from pin 12 to the 6840 pin 28. I'm sure that will be OK but might as well confirm. Lastly can you post a pic of that area with chip in. There's got to be an obvious answer to this but I'm scratching my head at present.
  3. Yesterday
  4. Can’t find any issues with the socket or the traces from it, even if I leave pin12 out the socket I still don’t see the signal on the pin on this board the trace on pin 13 looked slightly shallower than on the working board but was still near 100hz
  5. Lol yeah that stumped me I was checking vcc arse for tit! But once I realised vcc is fine as is ground And I see what you describe on a working board, so god knows what's happeng here?
  6. Please forgive me for mentioning this but pin 1 is top right hand as you look at the board.
  7. I know it's a bummer! Vcc is fine on the chip too, I must be missing something, going away to compare to a working board
  8. Don't understand that Ronnie? If the 100Hz is going in it should come out as a nice 100Hz square wave about 5v p2p assuming the chip is powered ok. Pin 12 feeds IC2 (6840) and IC3 (6821) but I can't believe they would be causing anything.
  9. Ark Aid Repairs is repairing it.
  10. Got the new chips today so pin12 still the same! Pin13 is like this does that look right? Sometimes it will come up with 50pm loked alarm on the alpha when I’m probing ? thanks Ronnie
  11. Last week
  12. Great work again bob and there's no end to the 3d printing capabilities. The mpu3 boards seem somewhat wrong without the cart surround protector so a very worthy project .
  13. Nice to see an admc machine crop up .has to be worth £60 just for the parts
  14. I have a few 80s mpu4 game cards... I'll.check and let u know tomorrow ..
  15. It's a tantalum capacitor so there's a good chance it has! Snip it off and try it again.
  16. They shouldn't run hot, sounds like a chip has failed unless C1 has gone short?
  17. Will try thanks. The board got really hot after being plugged in for a few seconds.
  18. or take the roms out one at a time and clean the pins but make sure thay go back in the right way
  19. check in that white socket for bent pins
  20. Unbelievable 😂👍.great capture
  21. My last visit was great. I did a tour video to update you all.
  22. Your going to need to take a picture of the original card, there are a few different sorts!
  23. Hi all after some great advice here it appears I need a replacement program card for my mpu4 board. Think it is a mod2 but the machine is an 80s "stop the clock". Thank you all
  24. Hello everyone. First of all, I want to apologize because I don't speak the language of William Shakespeare. And everything I write is translated with Google. Let me introduce myself: Jean-Michel, 68 years old. French. A little fan of jukeboxes, pinball machines, and slot machines. I have two Barcrests and a Novomatic. A 1982 Barcrest Ambassador. I registered on your site to find information and probably ask questions. Thank you for your welcome and sorry for my poor English.
  25. Hello everyone. First of all, I want to apologize because I don't speak the language of William Shakespeare. And everything I write is translated with Google. Let me introduce myself: Jean-Michel, 68 years old. French. A little fan of jukeboxes, pinball machines, and slot machines. I have two Barcrests and a Novomatic. A 1982 Barcrest Ambassador. I registered on your site to find information and probably ask questions. Thank you for your welcome and sorry for my poor English. jm
  1. Load more activity
×
×
  • Create New...