Jump to content

All Activity

This stream auto-updates

  1. Today
  2. Bonjour a tout la page a charger pour une fois jen profite pour vous répondre oui la carte et salle état au niveau de la batterie je les retirais mais la led rouge (reset ) reste fixe et donc la machine ne l'allume pas , je suis dans l'attente de 2 carte pour piece que jai commande devrais arriver dans quelque jour
  3. Yesterday
  4. In most cases, it’s due to battery damage; you can even see the green corrosion. This unit needs to be refurbished. I happen to have the same unit here.
  5. That was the solution. The sound is working again, thanks. I’ll post the restoration process in a separate thread.
  6. Wow, it's been three years since I wrote up an MPS1 but done a fair few in that time. One I have on the bench at present has been driving me demented. It came in as a non boot and there were a lot of crusty chips all around the battery area. To cut a long story short every chip 14, 16 and one 8 way plus the 4x 20way buffer chips around the CPU were all bad. Luckily the Async chips (TMS9902) were OK as was the CPU, PAL and RAM but the reel CPU was toast which was a bummer. Anyway after changing all the chips out it was time to switch on. It came out of reset and ....nothing! Then followed about 3 days of trying just about everything. All the DATA and ADDRESS lines were checked for no shorts and that they all went to their correct places. The only clue was that the PAL chip was sending out invalid mem access? Desperation was beginning to set in so I thought I'd ask AI and see what it would come up with. After explaining the issue, uploading diagrams and stuff I awaited an answer. Thinking it might just say '42' it eventually replied and said 'I'd jump in Thames if I was you'! A few hours later and I was checking the DATA waveforms again and this time I had the scope set for different time period and I could see that the waveforms were slightly different either side of the buffer chip (74LS245). These buffer chips around the CPU are controlled by their enables on pins 1 + 19 and these in turn are driven from IC27 (7404) which had been swapped already as it was faulty and wasn't bring the enable lines down to 0v. Because the ADDRESS line chips were working I didn't look any further until I tested pin 19 on the DATA buffer chip and it was sitting at about 1v! Now pin 6 on IC27 was at 0v so there was a break in the track somewhere. Hurrah looks like I'm on to a winner. There was indeed a broken track which was rotten, you couldn't see it with the naked eye and not really under the microscope either. So in goes a patch wire and BINGO she boots! So was it time to wrap it up....nope, it now looks like there's a switch input error on one of the PIO chips but at least I've got something to work with. Watch this space.....
  7. Nice find, I love barn finds, It wil keep you buzzy for a while
  8. Jimxxx, thanks I replaced, a burned resistor,in the area. Will test the transistor if it's not damaged
  9. Hi, assuming this is similar to other mpu1 and mpu2 schematics then the speaker is connected to pin 15 on the blue with its other side going to pin2 (+15v). Again assuming there are no loose connections or dry joints on the board in that area then i would check the transistor connected to pin 15 which i think is T19. probably the one with the brownest resistor area as seen below. Good luck and post some pics.
  10. Hi all, a new project is arrived number 6 😆 Barcrest Mpu2 Starlight I have a problem, and worked in the past on same problem. but can't think the solution . I have no sound, mpu is stable (need revision) wen i swap the mpu, with spare I have sound. So, problem is the board.
  11. Last week
  12. Hello !! Phil has a bit of work to do, but it’s great that he found It. In any case, you have better luck than we do in France when it comes to finding machines to add to a collection. Machines of this type are rare or hard to come by here. Best of luck with the rest of your project! Thank you for the information.
  13. Yes there is, but they are nearly all digital s**t. But hey that’s just my opinion and other opinions are available. There are still arcades with old school machines around the country.
  14. Hello, Great find. I had a question: in your country, are there still slot machines in operation— in pubs, bars, or elsewhere—or are they prohibited, as they are in France? Thanks.
  15. Great find phil , and a £3 original too
  16. I know Ron, would look nice beside my lucky 2's but I need to thin out
  17. If only I had room I would go for that little gem.
  18. The green LED is power, it should stay lit. The red LED is reset, it should come on for a couple of seconds then go off and stay off. If it comes back on then the board is stuck in reset. Try turning off all the switches on SW1 and powering up.
  19. The green LED is power, it should stay lit. The red LED is reset, it should come on for a couple of seconds then go off and stay off. If it comes back on then the board is stuck in reset. Try turning off all the switches on SW1 and powering up.
  20. The green LED is power, it should stay lit. The red LED is reset, it should come on for a couple of seconds then go off and stay off. If it comes back on then the board is stuck in reset. Try turning off all the switches on SW1 and powering up.
  21. Been offered this but it’s too far for me! It’s down in Surrey I told the guy it would be worth around £100. If anyone here is interested?
  22. Bjour à tous jai demarer une autre discussion das section des nouveaux mais je ne peux pas consulter les message d'erreur ex0 du coup jen tente une autre ici pour le coup voici la machine en question équiper d'une carte simple astra IO-3 intégrer La carte reste mais le processeur reste figer led rouge fixe verte fixe aussi
  23. Bjour à tous jai demarer une autre discussion das section des nouveaux mais je ne peux pas consulter les message d'erreur ex0 du coup jen tente une autre ici pour le coup voici la machine en question équiper d'une carte simple astra IO-3 intégrer La carte reste mais le processeur reste figer led rouge fixe verte fixe aussi
  24. Bjour a tous jai demarer une autre discutions das section des nouveau mais je ne peux pas consulter les message erreur ex0 du coup jen tente une autre ici pour le coup voici la machine en question équiper d'une carte mere astra IO-3 integrate La carte demare mais le processeur reste figer led rouge fixe verte fixe aussi
  25. Earlier
  26. The green LED is power, it should stay lit. The red LED is reset, it should come on for a couple of seconds then go off and stay off. If it comes back on then the board is stuck in reset. Try turning off all the switches on SW1 and powering up.
  1. Load more activity
×
×
  • Create New...