All Activity
- Past hour
-
That was the solution. The sound is working again, thanks. I’ll post the restoration process in a separate thread.
- Today
-
Wow, it's been three years since I wrote up an MPS1 but done a fair few in that time. One I have on the bench at present has been driving me demented. It came in as a non boot and there were a lot of crusty chips all around the battery area. To cut a long story short every chip 14, 16 and one 8 way plus the 4x 20way buffer chips around the CPU were all bad. Luckily the Async chips (TMS9902) were OK as was the CPU, PAL and RAM but the reel CPU was toast which was a bummer. Anyway after changing all the chips out it was time to switch on. It came out of reset and ....nothing! Then followed about 3 days of trying just about everything. All the DATA and ADDRESS lines were checked for no shorts and that they all went to their correct places. The only clue was that the PAL chip was sending out invalid mem access? Desperation was beginning to set in so I thought I'd ask AI and see what it would come up with. After explaining the issue, uploading diagrams and stuff I awaited an answer. Thinking it might just say '42' it eventually replied and said 'I'd jump in Thames if I was you'! A few hours later and I was checking the DATA waveforms again and this time I had the scope set for different time period and I could see that the waveforms were slightly different either side of the buffer chip (74LS245). These buffer chips around the CPU are controlled by their enables on pins 1 + 19 and these in turn are driven from IC27 (7404) which had been swapped already as it was faulty and wasn't bring the enable lines down to 0v. Because the ADDRESS line chips were working I didn't look any further until I tested pin 19 on the DATA buffer chip and it was sitting at about 1v! Now pin 6 on IC27 was at 0v so there was a break in the track somewhere. Hurrah looks like I'm on to a winner. There was indeed a broken track which was rotten, you couldn't see it with the naked eye and not really under the microscope either. So in goes a patch wire and BINGO she boots! So was it time to wrap it up....nope, it now looks like there's a switch input error on one of the PIO chips but at least I've got something to work with. Watch this space.....
-
Nice find
-
Nice find, I love barn finds, It wil keep you buzzy for a while
-
Jimxxx, thanks I replaced, a burned resistor,in the area. Will test the transistor if it's not damaged
-
Hi, assuming this is similar to other mpu1 and mpu2 schematics then the speaker is connected to pin 15 on the blue with its other side going to pin2 (+15v). Again assuming there are no loose connections or dry joints on the board in that area then i would check the transistor connected to pin 15 which i think is T19. probably the one with the brownest resistor area as seen below. Good luck and post some pics.
-
HenryPaunc joined the community
-
JamesUrbah joined the community
-
Edwardshawl joined the community
-
Hi all, a new project is arrived number 6 😆 Barcrest Mpu2 Starlight I have a problem, and worked in the past on same problem. but can't think the solution . I have no sound, mpu is stable (need revision) wen i swap the mpu, with spare I have sound. So, problem is the board.
- Yesterday
-
Hello !! Phil has a bit of work to do, but it’s great that he found It. In any case, you have better luck than we do in France when it comes to finding machines to add to a collection. Machines of this type are rare or hard to come by here. Best of luck with the rest of your project! Thank you for the information.
-
SamuelAdume joined the community
-
Georgemop joined the community
-
Martinbub joined the community
-
Williambab joined the community
- Last week
-
Yes there is, but they are nearly all digital s**t. But hey that’s just my opinion and other opinions are available. There are still arcades with old school machines around the country.
-
Hello, Great find. I had a question: in your country, are there still slot machines in operation— in pubs, bars, or elsewhere—or are they prohibited, as they are in France? Thanks.
-
sulzerned started following Barn find reel crazy
-
Great find phil , and a £3 original too
-
I know Ron, would look nice beside my lucky 2's but I need to thin out
-
If only I had room I would go for that little gem.
-
The green LED is power, it should stay lit. The red LED is reset, it should come on for a couple of seconds then go off and stay off. If it comes back on then the board is stuck in reset. Try turning off all the switches on SW1 and powering up.
-
The green LED is power, it should stay lit. The red LED is reset, it should come on for a couple of seconds then go off and stay off. If it comes back on then the board is stuck in reset. Try turning off all the switches on SW1 and powering up.
-
The green LED is power, it should stay lit. The red LED is reset, it should come on for a couple of seconds then go off and stay off. If it comes back on then the board is stuck in reset. Try turning off all the switches on SW1 and powering up.
-
Been offered this but it’s too far for me! It’s down in Surrey I told the guy it would be worth around £100. If anyone here is interested?
-
Bjour à tous jai demarer une autre discussion das section des nouveaux mais je ne peux pas consulter les message d'erreur ex0 du coup jen tente une autre ici pour le coup voici la machine en question équiper d'une carte simple astra IO-3 intégrer La carte reste mais le processeur reste figer led rouge fixe verte fixe aussi
-
Bjour à tous jai demarer une autre discussion das section des nouveaux mais je ne peux pas consulter les message d'erreur ex0 du coup jen tente une autre ici pour le coup voici la machine en question équiper d'une carte simple astra IO-3 intégrer La carte reste mais le processeur reste figer led rouge fixe verte fixe aussi
-
Bjour a tous jai demarer une autre discutions das section des nouveau mais je ne peux pas consulter les message erreur ex0 du coup jen tente une autre ici pour le coup voici la machine en question équiper d'une carte mere astra IO-3 integrate La carte demare mais le processeur reste figer led rouge fixe verte fixe aussi
-
The green LED is power, it should stay lit. The red LED is reset, it should come on for a couple of seconds then go off and stay off. If it comes back on then the board is stuck in reset. Try turning off all the switches on SW1 and powering up.
-
Hi Snou Sorry to say it is not a tech i have had anything to do with so i have no idea what the sequence of the LEDs is. But from looking at the photo of the PCB, how bad is the leakage in the battery are? Can you take a close up photo of that area? Also i would want to check the integrity of U1 EPROM as the label has fallen of its window and if this has been exposed to light / sunlight for a period of time it could have damaged the program. Just to save anyone having to use translate i have attached it below. Cheers Jim +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ Hello everyone! I’m new here—my nickname is Snou, and I live in France/ I’m reaching out because I own a "Club Millionaire" slot machine made by Astra. The machine is complete, but it won’t turn on. The power supply seems fine and is delivering power. Regarding the main circuit board, the battery (the "pill") had leaked and has since been replaced. The two LEDs light up, but they remain steady (they don’t flash). Could you please help me? Best regards, Snou ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
- Earlier
-
snou started following Club millionnaire
-
Bonjour à tous ! Je suis nouveau, je me surmôme snou et je vie en france Je viens vers vous car je pocede une machine a sous club millionnaire de la marque astra , La machine et complète mais ne sallume pas L'alimentation me semble bonne et délivre du courant Concernant la carte simple la pilule à couler et à etais changer Les 2 LED s'allument mais restent fixes Pourriez-vous maider ? Cordialement, Snou
-
Bonjour à tous ! Je suis nouveau, je me surmôme snou et je vie en france Je viens vers vous car je pocede une machine a sous club millionnaire de la marque astra , La machine et complète mais ne sallume pas Lalimentation me semble bonne et délivre du courant Concernant la carte simple la pilule à couler et à etais changer Les 2 LED s'allument mais restent fixes Pourriez-vous maider ? Cordialement, Snou
-
I now have everything i need for this one
