Jump to content

Leaderboard

    [[Template core/front/popular/memberRow is throwing an error. This theme may be out of date. Run the support tool in the AdminCP to restore the default theme.]] [[Template core/front/popular/memberRow is throwing an error. This theme may be out of date. Run the support tool in the AdminCP to restore the default theme.]] [[Template core/front/popular/memberRow is throwing an error. This theme may be out of date. Run the support tool in the AdminCP to restore the default theme.]] [[Template core/front/popular/memberRow is throwing an error. This theme may be out of date. Run the support tool in the AdminCP to restore the default theme.]]

Popular Content

Showing content with the highest reputation on 10/18/20 in all areas

  1. Sound roms in the downloads section and sent to the layout creator ๐Ÿ˜€
    4 points
  2. Hey guys, apologies for the lack of updates. I've had a busy couple of months and haven't had much free time to work on her lately, however the last couple of days I've finally had time to work on the mini logic board. The majority of the nudge lights were lighting in the wrong sequence (for example 10 nudges would show as 4, and 9 nudges as 2). I'm pretty sure the fault was caused by a seriously corroded pin on the "A" input of the LS138, ( the one Matrixnet UK circled in his reply above), however all 4 of the IC's on that board were showing serious corrosion, so i decided to replace the lot. I managed to get all of them out without any damage to the board, and have installed sockets ready for the new IC's. I haven't had chance to test it in the machine yet as I still have the reel unit and motherboard removed, however all the sockets test fine with the multimeter and I'm very happy with how it went. Thanks very much for all the advice on tempertures and removal tips. Next up are the sound issues, (which I'm pretty sure is due to the fact that the capacitor right next to the IC responsible for the sound, has leaked and needs replacing)
    3 points
  3. Here you go mate Dave asked me to upload this for you. bluemoonยฃ6token.BIN
    2 points
  4. BFM - Club Wild West Tech: Scorpion 2 Here's a 90's 3 reel clubber from Bell Fruit. It plays a fun game. Keyboard shortcuts in the notes section of the emulator. Thanks as ever to Wizard for the emulator Geddy for letting me use his & bugs bfemulator layout as a guide. Popeye for the sound rom The rom and image providers. Please use MFME V19.8 or later to play. Club Wild West.zip
    1 point
  5. R211 is 2.7R Get a single pole DIL switch for SW1. There's lots more info on my workshop thread for Scorp1. Good luck.
    1 point
  6. Hi i have one of those what parts are you missing?
    1 point
  7. Thanks for the update Clo and to Popeye rom provider. Much better with sound.
    1 point
  8. Sound Rom added, thanks to @Popeye
    1 point
  9. I recommend you take pictures as you take disconnect or take anything apart to help you put it back correctly. Good luck with your restoration.
    1 point
  10. Nice one Popeye, thanks heaps bud๐Ÿ˜Š
    1 point
  11. 1 point
  12. Hi Matt, great post thanks for sharing, will look forward to seeing you get her up and running once again ๐Ÿ™๐Ÿป
    1 point
  13. Hey Matty, if you go down the reel lubrication route I was given some advice many moons ago that if you peel the label off the motor you can spray some lube directly into the reel motor, leave it on its side overnight to give it a chance to get thoroughly into all the parts of the mech, instead of completely dismantling the motor itself I have done this and it made a difference you will of course have to re-glue the sticker back on or in my case i placed a new piece of electrical tape over the aperture.
    1 point
  14. Hi Matty, my Eachway suffered with attract lights out and weird sequencing but once i replaced this chip all was good ๐Ÿ™‚ Good luck with your project
    1 point
×
×
  • Create New...